Door and window cover base construction process and matters needing attention

Door and window cover base construction process and matters needing attention

definition

Door and window cover: In the vertical surface of the two vertical edges of the door and window openings, the external wall can be formed to form a frame and can also be flush with the external wall. It is necessary to stand vertical and flat and to meet the wall surface. Therefore, the quality requirements are high. This is like a regular cover on the door and window cover, people used to call it door and window cover.

Door and window frames refer to the doors and windows attached to the glass used to secure doors and windows or doors and other objects belonging to the doors and windows.

Door and window sticking: When the door and window frame are flush with the inner wall surface, there is always an obvious seam with the wall surface. This seam is also present when the door and window use the cheeseboard. The bound wood board cover seam is used to cover the seam. The article is called a face.

Door and window cover construction process

1. Check the selection of the base material for wood keel and 15mm blockboard or MDF for the base material. Before the construction, check the error of the flatness of the base wall exceeds 30mm. Use the corresponding measures. After the wall is well damaged, apply the cement mortar to make up the leveling and then make the surface finish.

2, the door and window cover grass base board block material laying base with a dry wood hit the wooden wedge fixed 5mm from the ground to prevent flooding. The use of white latex on the cover plate and nails to fix the white latex should be used to brush the plate.

3. The thickness of the door leaf is generally about 38mm. The specially reinforced wood board at the lock can be cross-opened to prevent deformation.

4. Installation of door and window sash: The distance between the door and the window (surface height) is 5-8mm, and the left and right upper door gap is 2-3mm. The door leaf is combined with the door and the tight gap is less than or equal to 2mm. The hinge position is 1/10 of the standing height. Door-moving fans involving frosted glass should be played in the smooth part of the glazed glass after the appropriate amount of glass glue protection glass kitchen and bathroom matte surface should be outside the junction where the matte surface should be inward.

5. The installation hinge must be double-sided on the door leaf and the door frame. The opening and hinge of the door leaf are tight.

6. The height of the door lock from the ground 900-1000mm (the center of the lock) The position of the lock hole The gap between the correct lock tongue and the door leaf lock and the door frame should be tight. After the lock is installed, it must be bandaged to prevent contamination.

7. Sliding door: Use the small slide rail within 1500mm of the door and window sash; use medium 1500-2000mm; use large slide rail above 2000mm. When determining the width of the double-leaf double-track sliding door leaf, the overlapping edges of the two leaves should be more than 10 mm. Horizontal and vertical joints should be uniform, tight, hidden sliding doors should be closed after the door is installed and qualified.

8. During the construction, special attention should be paid to the treatment of the upper part of the door cover and the upper and lower side of the door leaf.

9. When the spring door is installed, the door should be drilled and the door should be drilled. The shaft should be opened on the ground. The upper and lower axis of the spring should be on the same vertical line. The spring should be buried flush with the ground. Fine concrete should be used for irrigation. Both sides of the spring rocker fan and the door fan should be tightened.

10, door cover base plate with the plate does not allow horizontal use of longitudinal 2-3 with the entire board to leave 2-3mm stitching so as to prevent deformation of the grassroots.

Door and window cover construction notes

1, according to the requirements of the room and drawings made curtains box, if you do not directly install the curtain rod curtain box, in the installation of curtain rods, you should pay attention to the window frame and the length of the curtain rod thickness and length.

2. When making a panel curtain box, first make a 7-shaped frame pinned to the top, and both sides should be sealed with wood panels. The vertical border under the application of a 20 * 18mm wooden bar reinforcement, nailing, to prevent deformation, such as the re-sealed nails decorated with water, do mixed water paint must ensure that the grass-roots surface smooth.

3. When the window cover is made of block board or density board, the base board should be fixed on the keel of the window frame base and then nailed. The "zigzag" shaped nail prevents the curling of the line, the included angle should be dense and smooth, and the window cover The next mouth should use marble, so as to avoid deformation due to moisture.

4, the door cover should be made of wood frame, planing, planing straight, and then in the assembly molding installed on the wall, covering the base board and veneer.

Door and window cover acceptance criteria

1. The door cover shall be vertical, the veneer shall be smooth and square, and there shall be no phenomenon of size or flare;

2. The cutting angles of wooden doors and window covers are neat, the joints are tight, the surface is smooth, there is no planing, and burrs.

Renovation Construction Knowledge Window Glass Home Improvement Cement Home Improvement Decoration Glass Block Marble Tile Glass Glass Sliding Door Kitchen Sliding Door Glass Door Kitchen Glass Sliding Door Bathroom Waterproof Bathroom Sliding Door Bathroom Tile Bathroom Door Exterior Wall Tile Tile Rubber Kitchen Tile ld Tile

Full Elevator Replacement

A completely new elevator to replace the old one


WHEN TO REPLACE AN ELEVATOR?


We recommend full replacement if your elevator has a small, cramped car, takes a long time to travel between floors, is often out of order and is 15 years old or more.

With CEP full elevator replacement you will improve user safety and comfort, increase building values and reduce unplanned repair costs. All this is possible hassle-free thanks to our installation process.

FULL REPLACEMENT SOLUTIONS


We offer 30 eco-efficient full elevator replacement solutions. Find out more below.


Full Elevator Replacement,Mrl Commercial Elevators,Hospital Bed Elevators,Residential Elevators

CEP Elevator Products ( China ) Co., Ltd. , https://www.zjfullelevatorreplacement.com