The decoration spent more money, and it was unsatisfying to live in. You must have been blinded by the construction worker's cutting corners. Renovation, if you do not have a little experience, it is very common to encounter this kind of situation. However, it is certainly too late to make up for the decoration knowledge. Here are 10 common ways of cutting corners and materials. Remember! Means one: wall painting less than two times Steal workers index: ★ Phenomenon: Latex paint is the most common wall decoration material. It can be painted or sprayed in specific construction. For the interior decoration of the room, the general latex paint needs to be painted twice or more to be qualified. If the workers are not serious or perfunctory during the construction, there will often be a color difference, especially the darker emulsion paint will appear. problem. Reminder: A certain amount of water must be added before the latex paint is used. The latex paint must be used up once. The paint of the same color is best applied once. Means II: Lazy to cause poor plumbing Steal workers index: ★ ☆ Phenomenon: The completion of the house decoration has no problem on the surface, but it will not be long before the sewers in the kitchen and bathroom are found to be sluggish. This is caused by the lazy construction team. In order to save time, the construction team may pour concrete pieces containing cement and sand directly into the sewers, causing poor drainage pipes. Reminder: After the completion of the waterway construction, all basins, basins, and bathtubs should be filled with water to see if the water is open and whether there is any leakage in the pipeline. After all these steps have been completed, acceptance is accepted. Means three: do not wire according to requirements Steal workers index: ★ ★ Phenomenon: After a period of time after the renovation is completed, consumers use electrical appliances, especially water heaters and air conditioners that consume a lot of power, and the electrical switches and outlets will be hot and even burned. Some inexperienced consumers will consider it to be large. Power appliances are in trouble. Actually, this is not the case. This is most likely caused by the fact that the electrician did not wire the construction requirements when installing sockets, switches and lamps. Reminder: After all switches and sockets are installed, be sure to try them and see if there is a fever in the switches of these appliances so as to prevent electrical losses due to circuit problems during the subsequent use of electrical appliances. Means 4: Stealing and reducing materials to cause wall and floor tiles to be uneven Steal workers index: ★ ★ ☆ Phenomenon: If the decoration workers cut corners, it is prone to problems such as empty tiles, missing seams, and the like, and over time, tiles are prone to cracking and crushing. In addition, there are also particular concerns about cements and adhesives used for paving tiles. If the mix ratio is unreasonable, there will be some cases of shedding. Reminder: Wall tiles should be flat and solid, no dirt and grind marks, the surface color is basically the same, the joints are even, there is no cracks in tiles, drop angles and lack of edges. Means 5: No plans for buried pipelines Steal workers index: ★ ★ ★ Phenomenon: Today's home renovations generally choose to bury underground pipelines in order to maintain the simplicity and safety of the living environment. To bury underground pipelines, it is necessary to grooving walls and floors before embedding. A few workers are barbaric when they slot, which will not only damage the building's load-bearing structures, but also damage other nearby pipelines. Reminder: Before construction, we must reconfirm the direction and location of the pipeline with the construction team leader. The requirements for slotting are different for different wall structures. Means six: seams modified perfunctory Steal workers index: ★★★☆ Phenomenon: In some places where the wall and the door and window are docked, and where the two different colors of paint are docked, it is not easy to be noticed. Therefore, these places are also where the decorators work, and latex paints and other paints are prone to occur. Mixed with each other, there are various problems at the seams. Reminder: If there are two colors of paint on the wall facing each other, apply adhesive tape on the edge of the first color and then apply another color of paint. Means seven: Room alignment without leaving the base map Steal workers index: ★★★★ Phenomenon: In home renovation construction, almost all the wires are buried in the PVC pipe and buried in the wall. Therefore, after the electric wires penetrate the PVC pipe, consumers cannot see it at all, and they cannot accept it. If the worker is not careful in the operation, it will cause the wire to be entangled in the tube, causing hidden troubles. If workers deliberately cut corners, they will use wires with joints or put several wires in the same PVC pipe. Once a problem occurs, replacement is more difficult. Reminder: After the cable is installed, it must be checked for electricity. The consumer must leave the decoration staff with a pipeline map. When the electrician buried the wires in the wall, they could number the walls and draw a plan, and then use the strokes to draw the direction and the specific location of the wires, and indicate the position on the floor, down from the ground and adjacent walls, especially The location of the pipe joints should be marked so that in the event of a fault, the line position can be found immediately. Means 8: Handling of small facets of objects does not pay attention Steal workers index: ★★★★☆ Phenomenon: The so-called "small face" is a small place that consumers do not pay much attention to. For example: The upper edge of the door, the underside of the window sill, etc., where some workers will cut corners, or even do nothing. Reminder: Don't ignore any details when checking the quality of the project. Means 9: The ground is not leveled and the floor is uneven Steal workers index: ★★★★★ Phenomenon: In some projects where there is a suspicion of cutting corners, it is often found that there is a phenomenon of tilting at the edge of the wooden floor of the home, especially near the corners of the wall. This is due to problems with ground leveling. Because some houses are not well-grounded, they need to be re-leveled before laying the floor. If the workers are not careful, they will cause “more and more inequalityâ€. This will cause hidden troubles in the future. Reminder: Prior to leveling the ground, ground handling should be done first, then cement mortar should be used to level the ground. After the cement is dry, determine the flatness of the entire floor using a dedicated level ruler, and then do the next step. Means 10: Substrate processing coarse branches Steal workers index: ★★★★★☆ Phenomenon: Before applying latex paint and paving the wall and floor tiles, we must do a good job on the surface treatment of the wall or the ground. For a new house, the basement treatment generally only needs to be ground with coarse sandpaper, it is not necessary to remove the original paint layer, and the wall of the old house must be removed after the original paint surface before the next process can be carried out. Some workers use homeowners' knowledge of this knowledge and cut corners during construction. The consequences of this result are uneven walls, poor coloration after painting, and discoloration, cracking, and even loss of latex paint. Peeling, or tile paste is not strong. Reminder: In the paving construction of tiles, pay attention to the tiles can not be directly laid on the surface of lime mortar, lime cream, lime paper plaster, hemp stone mortar and latex paint, but to clean the base surface can be laid . The adhesive paste used between the ceramic tile and the base shall be formulated in strict accordance with the construction standards and proportions, and the specified grades of cement and adhesive glue shall be used, and they shall not be randomly deployed. When applying latex paint, be sure to pay attention to whether the wall putty is evenly and smoothly scraped, polished and brushed in place. Decorated caterpillar Three trees Paint porch Decorating paint Latex paint Electrical coating Cement floor tiles Doors Doors Bathroom tiles Colors Bathroom tiles Bathroom tiles Bathroom doors Tile adhesive Floor tiles Kitchen tiles ld Tiles
We diviided the led light according to the using eviiroment. Most of our product is the commercial LED Lighting
Commercial lighting is a term used to describe lighting that is used in commercial spaces, including auto dealerships, distribution centers, churches, factories, offices, and warehouses. Unlike residential lighting, commercial lighting is made to withstand more abuse and has a longer lifespan.
While the focus of residential lighting is often on aesthetics, commercial lighting is task orientated. Commercial lighting systems are designed based on what the application is. For example, in an office-type setting, you may see task lighting, which illuminates specific areas where employees need concentrated light to be able to perform their jobs.
150W Led Flood Light,100W Led Flood Light,Led Flood Light Garden,Led Flood Light Commercial Outdoor Jiangmen Dilin Lighting High-Tech Co., Ltd. , https://www.jmdilinlighting.com
Spring curtains curtains
Links: "Warm Water" and "Lock Water" for Wood Furniture in Winter
Beware of the following 10 types of decoration and work-reduction traps