When the decoration season arrives, the decoration of each household is avoided. The quality of cabinets directly affects the use of the kitchen. The problems such as door deformation, panel protrusion, and hardware failure have also plagued consumers. Is the product quality but off? Or is it the end of the year? These are the deadliest cupboards that kitchen cabinets cannot avoid? In fact, unqualified installations have caused these problems to a large extent. In order to visit the cabinet installation on site and help consumers understand the importance of cabinet installation, we came to Ms. Chen’s home. Ms. Chen’s home renovation is nearing its end, and the kitchen’s custom is a whole kitchen cabinet with kitchen appliances. Including two sets of cabinets, a set of cabinets, a range hood, a set of stoves and a basin. The cabinet is about 3 meters long. Ms. Chen introduced that the set of cupboards cost about 20,000 yuan in total. The installers came in at about 9:30 a.m., including the installation of the countertops, and completed the installation and cleaning work at approximately 3:30 in the afternoon. â— Tips â— Hidden parts are difficult to "check" after installation, the three most important load-bearing links are most likely to be cut corners The unqualified installation "HOLD" cannot withstand the theoretical ten-year or even longer service life of the cabinets. Some of the hidden details in the cabinets are the chief culprit in the sharp drop in cabinet life. "Deformation" is the most common problem that arises in the use of cabinets and affects the various uses of cabinets. Better support and load-bearing systems maximize the protection of the cabinet cabinet itself so that it will not be deformed during long-term use. Although these support are purely "extra" compared to conventional support, they are indispensable. Back panel stretch bar: In order to prevent the deformation of the cabinet, there are stretch bars in the middle of the back panel behind the cabinet as additional support. The back panel is the thinnest part of the cabinet body. Its load-bearing capacity and stretching capacity are relatively weak. However, once a problem arises, it will affect the entire cabinet, resulting in deformation of various parts. The material of the stretching strip is the same as the material of the cabinet cabinet. For Ms. Chen's cabinet, the material of the stretching strip is a solid composite panel. The installation location of the stretch bar is hidden, unless the owner pays attention to the assembly process, otherwise the owner is hard to see its “real bodyâ€. Cabinets equipped with tensile bars have largely reduced the deformation of the cabinet cabinets, in particular the problems such as the depression of the base plate and the deformation of the cabinet doors. Countertop load-bearing: It is not uncommon for cabinets to be spliced ​​on the countertop surface, and more people are focused on the seamless and polished surface of the spliced ​​part of the countertop. In fact, making the countertop look like a whole is not the main thing. How to protect this joint from cracking and misalignment in the future is the key issue. Can not rely solely on the power of glue, extra support is very important. Ms. Chen’s cabinet panel seams are above the chest of drawers and there is no excess support just below. So after the panel's docking and pasting process, the worker cuts out two pieces of palm-sized stone again and sticks it from the lower part to both ends of the joint. This detail is mainly to ensure the load-bearing joints, play an auxiliary bonding, to prevent deformation, bearing and so on. Ensure that the table will not bulge in the future, affecting the service life. Water tank load-bearing: The length of the water tank is slightly larger than that of other base tanks. Therefore, underneath the water tank, the workers added a load-bearing cupboard leg to make the water tank a “five-legged cupboard†to ensure that the floor would not be excessive Bearing deformation. In addition, a small accident at the beginning of the installation also shows another function of the leg: height can be adjusted. Since Ms. Chen’s kitchen originally used a balcony, an air-conditioned drain line passed through the kitchen, but the height was not “routed†according to the drawings given by the cabinet designer. Therefore, after the worker measured and communicated with Ms. Chen, Temporarily decided to increase the height of the 3 cm cabinet to avoid the pipeline. In addition, the height of the cabinet itself is fixed, and some housewives take into account their own height and cabinet countertop should be a certain proportion, the cabinet height should vary from person to person, but also by adjusting the height of the cabinet leg to solve. â— Tip two â— Drawer installation accuracy influences the use of hinges without loosening the door The most difficult part of cabinet installation is the assembly and installation of drawers and baskets. People who use cabinets have such feelings: If drawers and cabinet doors are not good, they will feel that the cabinets are not easy to use, and that their gestures are like being “under the cheeksâ€. We are accustomed to think that hardware is the only key that affects the flexibility of the joints of cabinets. In fact, the installation of the cabinet itself also plays an important role. On the one hand, the drawers must be tightly assembled when assembled. Minor deviations may cause the drawers to rub against the cabinet during sliding and affect their use. On the other hand, since the drawer and the panel are separately installed, the normal link should be to first assemble and install the drawer, confirm that there is no problem with the fitting of the hardware, and after the slide is normal, install the outer panel again. The panel and the door should be tightly fitted on the surface, but they cannot be squeezed against each other. This requires the worker to install it very carefully and carefully test it. The debugging of cabinet doors and drawers is very time consuming. Inside the cabinet, the hardware itself has reserved some organs, which can be moderately fine-tuned. For example, the height can be adjusted by the tightening of screws in some parts. Generally, cabinet doors use one year of cabinet door to begin to appear high and low deviations, pull the basket loose, the slide of the drawer becomes astringent and other issues, is due to the gradual looseness of hinges, hinges and other parts in use, self-adjustment can solve these problems. The astringency of the slide rail may be caused by the entry of rice grains, salt grains, etc. into the slide rail, and the slide rail needs to be cleaned periodically during use. Cabinets to buy hardware entrance decoration range hood decoration design cupboard cabinet door cabinet door cabinet counter kitchen cabinet door cabinet door drawer cabinet Bopp Adhesive Tape,Foam Sealing Tape,High Density Foam Tape ,Ultra Flexible Tape LONG TERM ELEC. CO., LTD , https://www.longtermhvac.com
"Three-point product seven points installation"