The bathroom is also called a washroom. The main facilities are: basins, toilets and bathtubs. There are also wall mirrors, towel racks, lighting, and moisture-proof exhaust fans. Conditional dehumidifiers can be dehumidified to reduce degassing and keep the interior relatively dry. Bathtubs are mostly enamel products, there are glass steel bathtubs and plastic bathtubs. >>> Link: Toilet Refurbishment Notes The bathroom decoration process is as follows: (1) According to the actual area of ​​the bathroom, choose the bathtub, basin and toilet that are of the right size and the same color pattern. (2) Transform the existing water supply and drainage system to meet new needs. (3) Choose a good position, place the tub, basin, and toilet in place and adjust the level to make it firm. Connect the upper and lower water pipes. Check whether the indoor distribution network is correct, whether the water distribution equipment and accessories have any faults, and pay special attention to whether the water trap is clogged or not, and whether the pipe joints are tightly sealed. (4) The hot water spout is mostly copper. When it is installed, it should be distinguished from the cold water spout. Because of the different conditions, the hot water sources are different. There are solar energy, liquefied gas, and electric water heaters. Of course, they also use the stove to heat hot water. (5) Completely inspect the water supply and drainage, and proceed with the next renovation if there are no problems. (6) Paste the glazed tiles. The large room can seal all the pipes. Laid low walls to cover the exposed part of the bathtub. Pick a glazed tile of the same color or suitable color as the bathtub to fully paste it. Adhesive can be 107 glue and high-grade cement mixture. The height of the glazed tile can be built to the lower end of the ceiling, so that the decoration effect is complete, and practical, easy to brush the wall surface. (7) A bath towel holder is attached to the upper part of the bathtub. Install the toilet paper holder next to the toilet bowl. The basin can be individually mounted as a towel rack or as a bench top. The washstand has a suspension type that does not occupy the ground, and can also be made into a cabinet type that can store things; (8) The wall mirror is mainly used for dressing, and is mounted on the front wall of the washstand or washbasin. Considering the high humidity in the bathroom, moisture treatment is usually done behind the mirror. The shape of the wall mirror is square and round, and the frame is mostly made of stainless steel, aluminum alloy, plastic, plexiglass and other materials with moisture resistance, and is suspended on the wall surface. For frameless wall mirrors, there are two ways to install. Fixation method is to cut the thick lens edging, drilling; wall with a hammer to drill, so that the hole in the lens and the wall, the hole embedded diameter 6MM expansion bolt; lens placed on the wall, so that the head of the bolt from Hole out of the lens hole, add rubber pad, tighten the dome chrome plated or copper nut. (9) The mirror headlight is the most commonly used local lighting in the bathroom. The light is bright and soft. The lamp has a fluorescent lamp type and an incandescent lamp type. The incandescent type uses a matte anti-fog lamp as the light source, symmetrically mounted on both sides or above the wall mirror. Fluorescent lamp type is more complex. The width and length of the lamp are selected according to the actual situation. The width of the sampan plate can reach the ceiling and go down to the upper end of the wall mirror. 20 centimeters from the mirror to make a closed space, install the fluorescent lamp in the upper part, and install the mobile frosted glass plate underneath. Glass matte is the role of the tone and light; the activity is to facilitate the replacement of the lamp and the starter. (10) The ground is smooth, and the non-slip glazed tiles of the same style can be laid, so the decoration effect is ideal. If the ground is uneven, it is necessary to use a mosaic (mosaic tile) with similar colors to lay the ground. The effect is good, and it is economical and practical. The adhesive used can be mortar made of 107 cement, cement and fine sand. The bathroom floor should be less than 2 cm above other rooms to prevent overflow from the bathroom. Another method is the adhesive method. Draw the position and shape of the mirror on the wall, make a mark, apply enough glass glue on the back surface of the processed 5MM lens, clean the wall surface, and press the mark to coat. The glued lens is pressed onto the wall, the lens is held by hand, and the force is uniform. The lower end of the lens is gently supported by the wood board, and then the lens is adhered by the tape. Larger and heavier lenses can be placed directly on the countertops of the allied washing station for bonding. After the glue is dry, remove the tape and clean it. The frameless wall mirror decoration effect is simple, clear and clean. Construction Acceptance Glass Room Interior Decorating Cement Lighting Decoration Style Glass Tile Stainless Steel Towel Holder Craft Glass Mirror Front Light Bathroom Exhaust Fan Bathroom Size
Clip Spring,Metal Spring Clips,Spring Loaded Clips,Stainless Steel Spring Clips
applicaiton: viation,automotive, motorbike, bicycle, automatic equipment, household appliance, medical device ,toy, telecommunication,computer, instrument and meter,furniture, electric tools,mold and other industries
China Clip Spring,Metal Spring Clips,Spring Loaded Clips,Stainless Steel Spring Clips, we offered that you can trust. Welcome to do business with us.
Clip Spring,Metal Spring Clips,Spring Loaded Clips,Stainless Steel Spring Clips Shenzhen Lanejoy Technology Co.,LTD , https://www.copper-nut.com
Toilet construction process