Everyone knows that the bathroom is a place where water is often used, so the work of moisture prevention is also very important. Face this more serious project. Some people want to know how to do waterproof bathroom . For this issue, let's talk about it in detail. This way you know how to operate the bathroom when you are decorating the house. Avoid the possibility of flooding the mountains at home. How to do a bathroom waterproof 1. Make sure the floor of the bathroom is relatively stable. If you need to replace the floor tiles of the bathroom, after you have cut the original floor tiles, you must first level the floor with cement mortar and then do waterproofing. This can prevent leakage of the waterproof coating due to uneven thickness. 2. The seam should be painted in place. The seam between the bathroom wall and the joint between the upper and lower water pipes and the ground is the most prone to problems. 3. Wall treatment is also very important. In the general bathroom waterproofing treatment, the wall surface should also be made of waterproof coating of about 30 cm high to prevent water from oozing through the wall. However, if the wall of the bathroom is a non-load-bearing light-weight wall, the entire wall should be covered with waterproof coating. 4, waterproof test must be done. After the construction of the bathroom is completed, all the water in the bathroom will be blocked, and a 25 cm high "can" will be built at the door, and then 20 cm of water will be poured into the bathroom. 5, keep the water flowing smoothly. All sewer pipes in the bathroom, including floor drains, plumbing pipes for sanitary ware, etc., should be kept open. Two bathroom waterproof operation 1, try not to damage the original waterproof layer In the newly delivered buildings, the floor of the bathroom, bathroom and kitchen have waterproof layers according to the relevant specifications. Therefore, leakage will not occur after the original waterproof layer is not damaged. The common problem now is that the bathroom facilities in the renovation will be added and the various water and sewage pipelines will be re-arranged or moved. The original waterproof layer of the building has been seriously damaged. However, there is no repair or re-waterproof construction. So that the problem was discovered after the leakage occurred. 2. It is necessary to replace the original floor tiles of the bathroom. After the original floor tiles are cut, the cement must be used to level the floor and then waterproof. This will prevent the waterproof coating from leaking due to uneven thickness. Before doing waterproofing, be sure to clean the floor and apply it repeatedly with polyurethane waterproof coating for 2 to 3 times. 3, must do wall waterproofing When the bathroom is bathed, water will splash on the adjacent wall. If there is no waterproof layer protection, the partition wall and the opposite corner wall will be mild and mildewed. Therefore, be sure to waterproof the wall before laying the wall tiles. Generally, the wall surface should be waterproofed to a height of 30 cm, but the non-load-bearing light-weight wall should be waterproofed, at least 1.8 m high. Waterproof can not be ignored for the bathroom, otherwise the frequent water leakage will affect the home environment and make many people feel bored. Xiaobian said that the toilet waterproof how to do so that everyone has learned a lot. If you still want to know more about the decoration information, please continue to pay attention to our decoration home network. Let your decoration no longer become a haunting problem. More related wonderful reading: What are the waterproofing of the restroom? Toilet waterproofing process Seal rings under [SEALMANN" trademark, have the advanced powder preparation technology with Seal Ring,Silicon Carbide Seal Ring,Silicon Carbide O Ring Seal,Sintered Silicon Carbide Seal Ring Ningbo FLK Technology Co., Ltd. , https://www.flk-global.com
independent intellectual property rights, with various molding technologies such as dry pressing,
isostatic pressing, squeezing & flow casting and different sintering technologies such as pressureless,
hot-pressing, reaction. We can supply our customers with high performance cost ratio and high quality
seal rings in various materials such as silicon carbide, nitride carbide, zirconia , aluminum oxide and
tungsten carbide. This series of seal rings are widely used in the fields of machinery, petroleum,
chemical industry, water treatment, aerospace, ship, metallurgy and nuclear power etc.
How to do the waterproofing of the bathroom, the waterproof operation of the bathroom