The tools and materials used for the general posting method of wallpaper are: glue, gypsum powder, brush, towel, sponge, sandpaper, knife, scraper, tape measure, center of gravity hammer, plastic container, etc. (1) The basic procedure for posting is: 1. Wall treatment: use scraper and scrape the wall surface impurities, floating soil, the crack of the cavity is smoothed with gypsum powder. If the wall texture is soft or has a powder layer, the wallpaper glue should be painted first. Make the wall firm and the wallpaper will not fall off. 2. Cut the wallpaper: first measure the height of the wall, then cut the length of the wallpaper, there are two kinds of cases: no flower wallpaper according to the height of the wall is cut about 10 cm length, as the upper and lower trimming: the flower wallpaper needs to consider the symmetry of the pattern Sex, so the cutting length should be increased according to the actual situation, usually more than 10 cm longer. 3. Applying glue: Apply the wallpaper glue to the back of the cut wallpaper with a brush. Pay special attention to the surrounding edges and apply the glue to ensure the construction quality, the coated wallpaper, and the glue to face the fold. 5-10 minutes (note that no external force should be applied to avoid creases in the wallpaper). After the glue is completely penetrated into the bottom of the paper, it can be posted, and several sheets of wallpaper are applied each time and posted in order. 4. Wallpaper construction: Use the center of gravity hammer to measure the vertical base line, and press the first wallpaper from top to bottom according to the base line. Use the squeegee from top to bottom, from the inside to the outside, gently scrape the wallpaper and squeeze out the bubbles. With excess glue, make the wallpaper flat against the wall. 5. Trimming and cleaning: Cut off the excess wallpaper on the upper and lower ends. The edge should be sharp to avoid burrs. It is best to use a new scalpel when cutting some wall coverings. Then use a sponge dampened with water to completely wipe the glue remaining on the surface of the wallpaper to prevent the wallpaper from turning yellow. If the wallpaper is dry after the wallpaper is dry, use a knife to cut the injected glue and flatten it to eliminate it. (2) Precautions during construction: 1. Before construction, you should carefully check whether the color number and batch number of the wallpaper are consistent. And to understand the type of wallpaper to be constructed, the color paper needs to be the flower, the plain paper should be applied in the opposite direction. 2. The quality of the glue will directly affect the overall effect and age of the wallpaper, so you need to buy the authentic brand of glue or wall powder. 3. Some wet backlit houses sometimes have a mold on the wall, preferably washed with disinfectant. 4. Dry paste, that is, the construction method of evenly applying glue directly on the back of the wallpaper, mainly for the rubber surface wallpaper. The wallpaper of the cross cloth and the non-woven bottom does not need to be glued. 5. The wallpaper with glue on the back should not be rolled into the water to avoid sticking. 6. The concentration of glue blending is judged by whether a chopstick can stand in the glue. 7. In case of a negative angle, the heavy hammer should be hoisted from the corner of the house that is 10 cm away from the corner of the house. In order to avoid deviations. 8. A patterned wallpaper, starting from the center of the wall and the height of the eye, usually from the combination of the two trims to align the repeating pattern. 9. During the construction of pure paper wallpaper, it is not allowed to scrape and rub the surface of the paper to avoid contamination of the wallpaper surface. 10. When any quality problems are found during the construction process, the construction personnel should be stopped immediately. To be resolved by the distribution staff. 11. Don't throw away the scattered wallpapers for later patching. 12. After affixing the wallpaper, open the doors and windows to keep the room ventilated. 13. When the wall needs to be hung with oil paintings or other ornaments, a “V†shape should be drawn on the wallpaper with nails for later repair. (3) Construction method of wall cloth construction method is basically the same as general wallpaper. be careful: 1. Since the wall cloth itself will absorb water, an appropriate amount of white glue should be added to the glue to increase the adhesion. 2. Do not use a hard scraper but a soft brush to avoid damage to the fabric. 3. If there is glue overflow, use a sponge to avoid damage to the fabric. (4) The basic method of tinfoil (metal) wallpaper construction method is the same as the construction of general wallpaper. be careful: 1. Wall treatment must be clean, dry and smooth. Because any convexity and concave condition of the wall surface is easy to appear after attaching a metal wallpaper. 2. Some wallpapers have been cut, while metal-faced textile wallpapers may have to be trimmed on the wall. For 24" (60.9cm) wide metal wallpapers. Cut at least 0.6cm from both sides. For 30" (76.2cm) wide patterned metal wallpapers, just follow the inside of the printed marking line. Cut it off. 3. If it is a landscape wallpaper, be sure to determine the order of the pattern after the trimming 3, the glue must be evenly applied to the wall, not directly on the metal wallpaper. Each time the glue is applied only to the range to be posted. 4. Use a soft brush to post. Since metal wallpapers do not swell or shrink, it is necessary to push out the bubbles at any time. 5, must keep the surface of the wallpaper clean, always clean the seams and excess glue spilled on the surface, clean water is often replaced. 6, pay attention to a layer of gold foil or tin foil on the surface of metal wallpaper will also be conductive, so be especially careful to avoid power lines, switches and other live lines. (5) Power switch and socket attachment method 1. After the main power supply is turned off, construction is carried out to avoid electric shock. 2, cover the wallpaper through the entire power switch or socket, cut two diagonal lines from the center point, there will be 4 small triangles and then remove the excess wallpaper with the utility knife along the power switch or socket. Wipe excess adhesive with a rag. (6) Matching strips The decorative strips are elegant in design and beautiful in color. They are usually used in conjunction with wallpaper colors. They can also be used separately with the paint wall. The purpose is to enhance the effect and atmosphere of the interior decoration by the elegant patterns and colors of the decorative strips. National decorative strips are already a necessity for interior decoration. They are widely used in various places, such as: homes, commercial buildings, entertainment spaces, etc., all indoor walls and ceilings: wall, wall, wall, or The beautification of the frame, such as: window frame, door frame, light frame, book frame, etc., as long as there is a traditional wire frame use, can be replaced or used together, the effect is very good if the creative and bold use of the trim, A finishing touch to the entire room. Length Cutting Machine,Cutting Machine,Cut to Length Machine Willing International Co., Ltd. , http://www.hz-rollformingmachine.com
Wallpaper posting method